The Dyna FS for quads is our hottest new product this year. Direct Plug in Performance. As used by winning pro racers worldwide. Now available to you! Available with features that will let you customize your quad, and make it the trickest, fastest, baddest one around. Non-Programmable Ignition Features Improved Timing CurvesHigher Rev LimitRemoved Reverse Rev LimitOverrides belt indicator for full performance at all timesEasier StartingIncreased Spark EnergyImproved Throttle ResponseEasier StartingPlug-In Module Replacement (Easy Mounting)TRX650 all years
Power Commander- plugs inline with your bike's stock fuel injection system. It uses OEM style connectors making installation easy and quick. The PCIIIusb allows a full range of fuel adjustment, as much as -/+ 100% over stock. Adjustments can be made either with a Windows based computer or by using the face plate mounted button adjusters. No permanent changes are made to the bike's system. Once the unit is removed, the bike reverts back to its stock settings
If you're looking to give your ATV extra pulling power by increasing torque then a gear reduction kit is the way to go!While an ATV may be a great performer on the trail with stock tire height, when larger mud tires are added for use in extreme conditions this can often leave a performance enthusiast wishing for more low end grunt. You can overcome this problem by using a gear reduction kit. A reduction kit is designed so that a stock ATV can turn the larger more aggressive mud tires without additional costly engine modifications. Once you install a gear reduction kit the motor doesn't have to work as hard to spin the tires which means it won't draw as much current from your batteries while it simultaneously increases torque to provide you with the traction and pulling power that you need.The system requires approximately 4-5 hours of labor by an experienced technician to install and is furnished complete with pictures and instructions. After installation, the RPM will be slightly increased, even with oversized tires. Tests have shown this increased RPM has not been objectionable. Gas mileage is essentially the same as the machine would get without the gear reduction system and with oversize tires installed. This product is carefully machined and heat treated for durability and long life.28 percent reduction
It's common knowledge that OEM parts were made to be JUST strong enough to get the job done. That's exactly why Gorilla Axle created a SUPER-STRONG Gorilla Duty CV Axle to pick up where the ATV manufacturers left off. Along with being much stronger than their OEM counterparts, Gorilla Duty Axles can take up to 40 degree angles which make them PERFECT for riders looking to install extended suspension lifts or oversize tires! Usually, after a lift in installed, stock axles are at their weakest point and cannot withstand the constant strain of the added stress of the angles. In time, this causes increased weakness...and eventually...breakage, stranded riders, and embarrassment! To handle the extreme angle caused by suspension lifts, the Gorilla Duty Axles have a uniquely designed, patented upper cv joint allowing them to articulate especially well compared to stock parts. However, being able to operate at high angles is only HALF of the special features offered by Gorilla Duty Axles. In order to withstand the extreme stress of high horsepower motors and SUPER-AGGRESSIVE oversized tires, Gorilla Duty Axles are made of 4340 Chromoly Steel, one of the industry's strongest steels, which is then machined to a precise fit for your quad! They are then heat-treated and cryogenically treated to ensure their absolute strength and durability. Covering the CV Joints are heavy duty Neoprene Boots filled with Lucas Oil Xtra Heavy Duty Grease to make sure the axles keep running as smoothly as when they were assembled even in the harshest riding conditions. Gorilla Duty Axles are assembled by hand in the Gorilla Axle Headquarters, located in Monroe, LA to fit the particular make and model needed by our customers. Gorilla Duty Axles come complete with a one-year limited warranty against breakage
The '06-Up Honda Rincon is factory equipped with a 675cc four stroke, 25" tires, 6.9" front and 8" rear wheel travel and 10" of ground clearance. Xtreme Products' 2" lift creates room for up to 28" tires. That combination results in a total lift height increase of 3.5" and 13.5" total ground clearance. Get the most out of your Rincon with the Xtreme Products 2" lift today. (Relocates top of shocks Front & Rear w/brackets).Xtreme Products lift kits are designed to provide maximum performance, durability, and enhance handling and stability characteristics while keeping installation simple and easy. Our designs help stabilize the suspension and make your ATV more sure-footed over rough terrain. Xtreme Products atv lifts provide the maximum lift available without causing costly damage to axles and related drive train components. Trail friendly lift systems built to get you in and OUT of the deep stuff.All Xtreme Products lift kits are precision engineered using A36 3/16 or 1/4 inch cold roll steel for maximum strength and reliability. Parts are laser cut then manufactured to exacting tolerances to provide the best value available. All Xtreme products are backed by a Limited Lifetime Warranty
High Lifter Lift Springs are a set of higher capacity replacement springs which are components of the stock shock absorbers. The original equipment spring is not heavy duty and is often fatigued early by heavy loads or continuous service. OEM springs tend to fatigue rapidly...even with low mileage.The High Lifter Lift Springs were engineered to provide about 100 additional pounds of capacity (per set) over the new stock springs. They were also designed to make a significant difference in the performance of your ATV with as little affect as possible on the ride and handling of the machine. The Lift Springs add some stiffness to the ride and decrease roll, but have not been found harsh or uncomfortable by anyone who has ridden them.And here's a big bonus! A complete set of the Lift Springs may be installed for substantially less than the cost of one replacement OEM shock. For those who ride at slower speeds, with big tires and heavier loads, the Lift Springs will be a welcome and economical upgrade.Depending on the make and model...and current modifications to the unit, the High Lifter Lift Springs have been known to add on full inch of suspension lift...however, it's not guaranteed. The Lift Springs add some stiffness to the ride and decrease roll, but have not been found harsh or uncomfortable by anyone who has ridden them.One thing is for sure. If you are a hardcore mud rider...or you carry a load...your ATV could stand a heavier load capacity. The High Lifter Lift Springs are just what the doctor ordered!APPLICATIONS:HONDA RINCON 650 (03-06)HONDA RINCON 680 (07-09)FRONT & REAR SPRING KIT
If you ride a Honda ATV, then YOU ARE AT RISK. Honda makes some of the highest quality ATV's in the industry. However, after a period of time and only moderate use, many Honda owners experience oil and smoke from the exhaust and/or loss of power. This can lead to hefty rebuilding costs, not to mention lost time on your ATV. Now, we have your answer. PROBLEM: On Honda ATV's, the recoil starter is located towards the rear of the engine, leaving the starter housing prone to filling with water and mud from even modest water crossings. The muddy water remains in the recoil starter because outlets are plugged with mud. Science will tell you that water causes more corrosion than any other element on earth. So naturally, with the mud and water trapped, the Honda recoil starter rusts and corrodes and is then disabled. In time, this water and mud will make its way into lower parts of the engine through the oil seal, causing severe damage to the performance of the ATV, ultimately leading to a ruined engine and a LARGE MECHANIC BILL! SOLUTION: There is a simple and inexpensive way to provide a permanent solution to this leaky situation. Install the Pull Starter Leak Shield on your Honda ATV and shield your engine from the expensive lower-end damage. The Pull Starter Leak Shield comes with simple installation instructions and bolts on easily after removing the recoil starter. The kit contains an aluminum shield (stronger than plexi glass), one gasket, one recoil adapter and mounting hardware.NOTE! The Pull Starter Leak shield replaces the OEM Recoil Starter. After installation, you will be unable to pull-start your quad.APPLICATIONS:650/680 Rincon 05-10
Includes tree trunk protector & D shackle. • 2500 lb pulling capacity. • 50 ft of durable 3/16 wire rope. • All metal 3 stage planetary gear train. • Fully sealed to keep out the elements. • Patented disc brake for excellent control. • Short throw clutch. • Handlebar mounted mini-rocker switch. • Limited lifetime warranty
Warn® 3000MT Winch • New mini-rocker switch with handheld plug. • Includes tree trunk protector & D shackle. • 3000 lb pulling capacity. • 50 ft of synthetic rope. • All metal 3 stage planetary gear train. • Fully sealed to keep out the elements. • Patented disc brake for excellent control. • Short throw clutch. • Limited lifetime warranty.
FOR BIGGER ATVs AND HEAVIER PULLING JOBS, THIS WINCH HELPS YOU GET THE JOB DONE IN THE FIELD AND ON THE TRAIL.With a mammoth 3,000 lb. pulling capacity, 50' of durable aircraft-grade wire rope, and a convenient handheld remote, the RT30 has the features you need to get the job done in the field and on the trail. No matter what the situation, the RT30's full sealing means the winch is prepared to do battle against the elements, and it's all-metal 3-stage planetary gear train will provide countless years of smooth, reliable operation. The patent-pending brake prevents rollback and will hold your vehicle securely on inclines. A standard handheld wired remote and handlebar-mounted mini-rocker switch increases your winching options so you can get the job done right.